PTFinish Version 1.3.2 (6/17/11) Release 
------------------------------------------

Master Change Log 
- Fixed an issue with the firmware updater.

PTFinish Version 1.3.1 (5/25/11) Release 
------------------------------------------
Package
     	PTFinish			1.3.1 	(5/25/11)
	logicnp				12.0.0
	DevComponents.DotNetBar		9.3.04
	CADImport			7.2.7.26044	

Master Change Log 
- Moved the stretch calibration to an expandable panel with an image of how the values affect the cut
- Maded it so Run 1 is not enabled when no cut file is selected
- Fixed loop test
- Added a keyboard for setting current settings.
 	
 

PTFinish Version 1.3.0 (5/10/11) Release 
------------------------------------------
Package
     	PTFinish			1.3.0 	(3/8/11)
	logicnp				12.0.0
	DevComponents.DotNetBar		9.3.04
	CADImport			7.2.7.26044
	
Master Change Log 
- Added CADImport viewer for faster views of hpgl files with zoom/move features
- Changed the Setup tab to only have cut file info
- Changed the run tab to have tension and enabling on it
- Got rid of the old setup Mode
- Added a loop test button
- Made the advanced output scrollable
- Made the right panel visible on all steps
- Moved the load input roll button to the right panel and renamed it
- Changed how cut groups are handled.
 	

PTFinish Version 1.2.4 (3/8/11) Release 
------------------------------------------
Package
     	PTFinish			1.2.4 	(3/8/11)
	logicnp				12.0.0
	DevComponents.DotNetBar		8.9.03
	

Master Change Log 
	- Added Strings
	- Changed some fonts for other languages
	- Changed Horizontal Target Offset
	- Fixed FW Updater to work with new FW
	- Changed some strings to better describe settings
	- Fixed metric issues with number of decimal places shown


PTFinish Version 1.2.3 (9/23/10) Release to Testing (1) 
------------------------------------------
Package
     	PTFinish			1.2.3 	(9/29/10)
	logicnp				12.0.0
	DevComponents.DotNetBar		8.9.03


Master Change Log 
	- Updated firmware update procedure to handle PGA update
	- Version 1.2.2 was an internal build
	- Setup resource file for translations
	- Fixed issue where max perf size was not being honored
	- Fixed UI refresh of Allow Perf checkbox



PTFinish Version 1.2.1 (9/21/10) Release to Testing (1) 
------------------------------------------
Package
     	PTFinish			1.2.1 	(9/21/10)
	logicnp				12.0.0
	DevComponents.DotNetBar		8.9.0
	

Master Change Log 
	- Added key for setting if blanks are used in batch job
		BlanksUsedInBatchJob
	- Added ability to handle full path in .ptip file



PTFinish Version 1.1.8 (7/6/10) Release to Testing (1) 
------------------------------------------
Package
     	PTFinish			1.1.8 	(07/06/10)

	- 
Master Change Log (From 1.1.6 to 1.1.8)
	
	Version 1.1.8
	- Added image to show which way upper takeup was turning.
	- Fixed issue with device connected/unconnected
	
	Version 1.1.7
	- Updated the Calculator form to describe what you are changing
	- Fixed Knife Home Error warning sticking in warn box
	- Added queueing for topix
	- On setup tab show errors when they occur (change page)
	- Added load input roll button
	- Fixed status in advanced dialog
	- Added Horz Target Offset in advanced dialog
	- Fix device connected logic
		-  if we have more than 6 bad status requests then go to unconnected state
	- Fixed issue where if we couldn't read status we might send invalid plot var command
	- Change mult knife decision logic to allow more cases.